All Rocket Kits
Airframes Composites Payload Bays Nosecones Recovery G-10 Fins Rings & Plates Motor Mounts Motor Retainers CPR Systems Staging Electronics Adhesives Hardware Igniters PML Gear Decal Sheets Gift Certificates Surplus Center
Build with the best!

PML "Dura-Chute" rocket parachutes are professionally made, multipanel, 15 degree conical design, rip-stop nylon construction.

If you have seen PML`s Dura-Chute parachutes out on the field, you know that we have the best parachutes on the market! Starting with the PAR-60 (60" diameter), we add heavy duty reinforcement webbing to each seam of the chute. This includes the seams between every panel, the skirt, the apex, and cord attach points. These are extemely rugged chutes!

"PML chutes were judged the highest in overall ratings of strength, quality, and appearance as published in an HPR Magazine report, The Great Parachute Driftoff."

All PML parachutes have a spill hole at the apex to reduce sway and drift. Approximate sizes (they may vary slightly) for the spill holes are shown below.

Also offered are Tubular Nylon Shock Cord, as well as various sizes of nylon recovery strap used in our piston systems. Tubular Nylon is many times stronger than elastic and is used in place of elastic for shock cord tethering. See our Complete FAQ on the FAQ Page for details on shock cord and strapping selection.

Parachute Sizing Upgrades -- PML chutes are sized for Midwestern and Eastern flying, as opposed to the open areas and hard landing surfaces of many Western sites. We size our chutes for minimal drift for smaller landing sites, while still allowing a safe descent rate into the grassy areas prevalent in the Midwest and East. However, if you`re flying in Western areas where drift is not as much a concern and where landing areas are harder (such as desert playa), or if you`re flying from high-elevation launch sites with lower-density air, we can upsize the chute in your kit. Upgrade pricing will vary depending upon the base and upgrade chute. As always, just ask when you order...PML will work with you on anything you`d like to do, kit or scratchbuild.

You`ll find the ability to upgrade to the next-size chute as a simple checkbox right in the area of the kit you`re ordering. As noted above, the pricing varies depending on the original and upgrade chute size.

If you’re scratchbuilding, check out our FAQ sheet for recommendations on piston strapping and shock cord selection criteria. Also check out the Parachute Size vs. Weight Chart for information on selection of PML `chutes for the weight of your rocket.

Click here to see how PML recommends you pack our `chutes
Click here to see how PML recommends you tie tubular nylon
Click here to see how much tubing is necessary to pack various PML chutes and tubular nylon.
Click here to see how to construct the PML piston system.


The PML Piston ejection system is the most reliable and effective ejection system ever developed for high power rocketry. You will never again need to stuff your rocket full of wadding or fiberglass insulation. Partial ejection caused by blow-by as well as burnt parachutes will become a thing of the past. Also, the nylon/rayon piston retaining strap is heat resistant and vastly reduces the zip cord effect encountered during early or late ejection by spreading the force over a much wider area than rope or cable. (The system must be incorporated during initial assembly).

The operation of the piston system is quite simple. The piston sits in the airframe "over" the motor and "under" the parachute. It is attached to the motor mount via the nylon strap which is epoxied to both the motor mount and the piston itself. When the ejection charge goes off, the pressurization between the motor and the piston bottom pushes the piston upward, which separates the rocket and pushes the chute out. That`s all there is to it. No special prep needed, nothing to do...just push in the piston, load the chute, and you`re done.



Part#Description Weight / Rating CostQty.

PAR-18 18" rip-stop nylon conical parachute, ~4" spill hole 0.6 oz. $25.95 TEMPORARILY OUT OF STOCK
PAR-24 24" rip-stop nylon conical parachute, ~5" spill hole 1.6 oz. $29.95
PAR-30 30" rip-stop nylon conical parachute, ~5" spill hole 2.4 oz. $34.95
PAR-36 36" rip-stop nylon conical parachute, ~8" spill hole 2.9 oz. $37.95
PAR-48 48" rip-stop nylon conical parachute, ~8" spill hole 4.1 oz. $42.95
PAR-54 54" rip-stop nylon conical parachute, ~10" spill hole 4.8 oz. $52.95
PAR-60HD Heavy Duty 60" rip-stop nylon conical parachute, ~12" spill hole 8.3 oz. $99.95
PAR-72HD Heavy Duty 72" rip-stop nylon conical parachute, ~14" spill hole 9.5 oz. $144.95
PAR-84HD Heavy Duty 84" rip-stop nylon conical parachute, ~16" spill hole. 11.9 oz. $189.95
PAR-96HD Heavy Duty 96" rip-stop nylon conical parachute, ~16" spill hole 18 oz.
(Special Order. Allow 1-2 weeks)
PAR-120HD Heavy Duty 120" rip-stop nylon conical parachute, ~20" spill hole 28 oz.
(Special Order. Allow 1-2 weeks)
STREAMER Heavy Duty Nylon Streamer 4"x144" --- $9.95
TN-0.56 Tubular Nylon, 0.56" 2000 lbs. $2.95/ yrd.
TN-1.0 Tubular Nylon, 1.0" 3100 lbs. $3.95/ yrd.
STRP-0.375 Strap Nylon, 0.375" (use like TN) 1000 lbs. $1.39/ yrd.
STRP-0.75 Strap Nylon, 0.75" 3000 lbs. $1.69/ yrd.
STRP-2.0 Strap Nylon, 2.0" 6000 lbs. $2.49/ yrd.
PS-1.5 Piston System Kit 0.75 oz. $9.95
PS-2.1 Piston System Kit 1.5 oz. $10.95
PS-2.5 Piston System Kit 2.0 oz. $11.95
PS-3.0 Piston System Kit 2.4 oz. $12.95
PS-3.9 Piston System Kit 4.0 oz. $13.95
PS-6.0 Piston System Kit 9.4 oz. $28.95
PS-7.5 Piston System Kit 20.8 oz. $32.95
Share PublicMissiles.com
Information about PML and our products
External resources

This site uses "Secure Server" Encryption Technology.
Your transactions are secure.
Copyright © 1997-2021 Public Missiles Ltd.
All rights reserved.
Built and Hosted by The Blast Zone
Contact the Webmaster with any website questions or comments